How to Build a Greenhouse (2024)

Mike BernerUpdated: Feb. 07, 2023

Step 1

Build the Foundation

We removed eight inches of topsoil to make room for our base layer of rock. We leveled and compacted the dirt, rolled out heavy-duty landscape fabric, then added at least a two-inch layer of 3/4-in. limestone.

Next, we created a mini retaining wall out of landscaping timbers. We placed, leveled and squared three sides of the retaining wall, leaving the fourth side off until dumping most of the rock.

We secured the timbers at the corners with eight-inch timber screws and fastened a pressure-treated board to keep the timbers together at the seams. When most of the rock was dumped and evenly spread, we built the fourth side. Then we leveled off and compacted the rock with a tamper.

Family Handyman

Step 2

Build the Side and Back Walls

To build the walls, we used pressure-treated 2x4s for bottom plates and cedar 2x4s for top plates. We cut them to the length of each wall and marked the stud layout on them.

Because the studs will be visible inside and outside, we wanted the walls to be symmetrical. So we found the center of the wall and marked the studs every 16 inches on-center from there. We nailed the cedar 2×4 studs through the plates, then fastened a second bottom plate.

After tipping up each wall, we kept it plumb with braces at each corner and nailed the corners together, making sure the top plates were flush on top.

Family Handyman

Step 3

Frame the Front Wall

Since the walls are only six feet tall and the door is taller than that, we didn’t frame its rough opening during this step.

We wanted all the walls tied together while we constructed the rest of the structure. So we built the wall all the way across, leaving out the center studs where the door will eventually be framed. We tipped this wall up, braced it plumb and nailed it to the side walls.

Family Handyman

Step 4

Anchor the Walls

We anchored the structure to the ground with bullet anchors by American Earth Anchor.

After drilling holes in the bottom plates to fit the anchors through, we drove the anchors into the ground with a hammer drill outfitted with a driving rod. Then we pulled the cable through the Quickvise washer to set the anchor in the ground and hold the structure firmly in place.

Family Handyman

Step 5

Repeat Parts With a Template

Make a template to accurately cut the rafters and assemble the trusses to ensure they’re all identical. We built a simple 2×4 frame on a pair of sawhorses and fastened a piece of sheathing to the top.

Be sure to build the frame to the exact span of the walls, then draw a line up from the center point to locate the ridge miter. We fastened a block 3-1/2-in. up from the corner on each side of the template at a 45-degree angle. With this setup, we could accurately mark and make all the necessary cuts before assembly.

Family Handyman

Step 6

Assemble Gable Walls

The gable walls on the front and the back of the greenhouse follow the same process as the trusses, with a few exceptions.

First, the gable ends are doubled up. Second, the collar ties are cut from 2-by material and fit between the two rafters. Third, we added cripples to match the layout of the wall they’ll be sitting on.

We used the same template to position the parts, then fastened the second top plate to the bottom of the trusses and cut the collar tie and cripples to fit.

Family Handyman

Step 7

Build the Trusses

After making the cuts, place the parts of the truss back on the template, line them up and fasten the peak together with a screw. Then cut and fasten 1×6 cedar collar ties. After determining the location of the collar tie, fasten another block to the template so you can repeat the location on the rest of the trusses.

Family Handyman

Step 8

Position and Brace the Gable End

We lifted the gable end onto the walls. Before tipping it upright, we fastened a few scrap 2x4s to the back of the wall to prevent the gable from slipping off.

We fastened a long board to the center cripple toward the top of the gable to use as a brace, pushed the gable upright and then braced it plumb. With it in place, we added a second top plate to the side walls where we’ll rest the trusses.

Family Handyman

Step 9

Position the Trusses

When the gable end is plumb, braced and fastened to the wall below, it’s time to set the rest of the trusses.

First, precut cedar 2×4 blocks to match the spacing of each stud bay. Fasten the blocks to the gable 36 inches from the peak, tip up the next truss, fasten it to the blocks and then add the next blocks. Repeat this for each truss until all are attached.

As we tipped up trusses, we checked that their tails lined up with the studs in the walls and toe-screwed them to the top plates.

Family Handyman

Step 10

Cut Out the Door Opening

Once you’ve fixed the trusses to the walls, cut away the top plates and a bottom plate to frame the door. We marked out a 42-1/2-in. opening in the center of the front wall and cut it out to fit the 36-in. door and its framing. This left room for the framing and space for the door to swing open.

Family Handyman

Step 11

Frame the Door

Cut king studs to fit from the bottom plate to the gable truss, plumb and fasten them in place. To finish the framing, add trimmer studs cut to fit the height of the door and a header across the top.

Because there is no doorjamb, these components must be perfectly plumb and level. Keep about 3/16-in. space at the sides and top, and about 3/8-in. at the bottom when the door is in place. Install the door temporarily to make sure it fits.

Family Handyman

Step 12

Sheathe the Bottom

To install siding on the bottom half of the greenhouse, we added sheathing to the studs. The sheathing also adds rigidity to the entire structure.

We ripped the sheets and nailed them to the studs with ring-shank framing nails, making sure all the seams landed on a stud. We kept the factory edge of the sheets up for easier leveling.

Family Handyman

Step 13

Add the Siding Sill

Before adding the siding, we needed to cut and install a siding sill to keep water from getting behind it.

We started by cutting a five-degree angle on the edge of a 2×4 with the table saw, then cut a miter at both ends to turn the sill around the corner. To get these miters to snug up at the corner, we matched the bevel cut with the miter saw.

We marked the miters and set the back of the board on a shim to keep the beveled edge flat against the fence. This trick makes it easy to make more precise compound cuts.

Family Handyman

Once cutting the miters, we cut a 1/4-in.-deep kerf in the bottom of the sill about 1/2-in. from the outer face of the sill. This kerf will keep water from wicking backward and getting behind the siding.

Family Handyman

We fastened 2×4 blocks between the studs to attach the sill. We set the sill on top of the plywood sheathing, flushing up the top of the blocks with the top of the sill. Then we fastened the blocks through the studs and the sill through the blocks.

Family Handyman

Step 14

Install Corner Trim

There are several ways to handle the corner detail of the siding. We chose an inverted corner trim that the siding butts into.

We used leftover 2x4s ripped in half and nailed them to the corners. This makes cutting the siding right up to the trim a breeze and adds a unique look. We also didn’t have to order thicker trim boards, spend time cutting angles into each piece of siding or install individual corner hardware for each course.

Family Handyman

Step 15

Install Siding

The corner trim makes the siding installation fast and easy. We recommend buying lap siding that’s long enough to span an entire side, if available.

Cut the siding to length and nail it to the studs using ring-shank nails compatible with cedar. (Some galvanized siding nails will leave a blue streak on the cedar when water passes over it.) Each course of siding overlaps the next, leaving six inches of each course exposed.

Family Handyman

Step 16

Finish Sheathing the Walls

With the sill and siding finished, we started sheathing the rest of the greenhouse walls with polycarbonate sheets. We cut the sheets to length, making sure each seam landed on a stud, then used two-inch stainless steel roofing screws to fasten the sheets.

Family Handyman

Step 17

Fasten the Fascia

Cut a piece of 1×6 cedar to fit beneath the edge of the roof. Fasten the fascia so that a straightedge placed on the rafter contacts the top outer edge of the fascia. Drive nails into each truss and top plate.

Family Handyman

Step 18

Make a Polycarbonate Sandwich

Apply a strip of butyl tape down the center of each truss. This tape is sticky, especially in hot weather! Cut the pieces of polycarbonate to overhang the fascia by about 1-1/2-in. Double-check the truss layout to verify that the edge of each sheet will land on a truss, then set the sheets in place.

Family Handyman

The butyl tape sticks to the polycarbonate instantly, so be precise when laying each sheet down. As you position the sheets, fasten a piece of cedar 1×4 over each truss with a three-inch exterior construction screw. Drive the screw through the butyl tape to seal the penetrations and secure the polycarbonate sheets.

To be on the safe side, we added a second strip of butyl tape where two sheets met on one truss to make sure all the screw holes would be sealed.

Family Handyman

Step 19

Trim the Roof

We trimmed the gable edges of the roof with 1×6 cedar. This batten needed to overhang the frieze board, so we positioned it one inch proud of the sheathing on the gable end. Then we installed cedar frieze boards to trim the peak.

We cut two scraps of 1×6 at a 45-degree angle to check the fit at the peak and fastened one of them temporarily. We positioned the frieze board on one side, then removed the scrap to install the other side.

Family Handyman

Step 20

Add Corner Trim

Cut 1×4 cedar boards to fit the sill and the fascia. Fasten them to fit around the corners with siding nails.

Family Handyman

Step 21

Fasten the Ridge Cap

To finish the outside of the greenhouse, we covered the peak with a polycarbonate ridge cap. We lined up the ridge of the cap with the peak of the roof all the way down and fastened it through each batten into the trusses with two-inch stainless steel roofing screws.

Family Handyman

Step 22

Install the Screen Door

We purchased a screen door from a home center to fit our door opening. We removed the screen and replaced it with a clear version of the polycarbonate we used on the rest of the greenhouse. Then we hung the door using three-inch galvanized utility hinges. Finally, we installed a screen door closer and fence gate latch to keep it from blowing open in the wind.

Family Handyman